Auxiliary circuit assisted soft switching techniques and their application to power converters

Files

Gurunathan_Ranganathan_PhD_1999.pdf (5.37 MB)

Date

2018-01-12

Authors

Gurunathan, Ranganathan

Journal Title

Journal ISSN

Volume Title

Publisher

Abstract

The need to incorporate significant improvements in power supplies is driven by customer demands, industry requirements and regulatory standards. For reduction in size and weight, it is imperative to process the power at a higher switching frequency. High frequency processing of power requires soft switching techniques to reduce the switching losses. Many soft switching techniques are reported in the literature to enhance the high frequency operation of power supplies. This thesis proposes novel high frequency, auxiliary circuit assisted, (a) soft-switched boost converters and their application to DC-to- DC converters and AC-to-DC front-end power factor corrected converters; and (b) zero-voltage switching (ZVS) dc link DC-to-AC inverters. In auxiliary circuit assisted soft transition converters, the auxiliary circuit processes the power during switching transitions, creating a soft transition path. In most of the proposed converters in the literature, the auxiliary circuit suffers from severe switching losses and switching stress. Discontinuous current operation of the auxiliary circuit results in parasitic oscillations between the switch capacitance and the resonant inductors increasing the stress on the devices. A zero-current switching (ZCS) auxiliary circuit and ZVS auxiliary circuit are proposed in this thesis to achieve soft transitions for the main circuit. A ZCS auxiliary circuit assisted soft transition boost converter is proposed. Operating intervals of the proposed technique in various intervals of operation are analyzed. Design constraints and considerations are discussed. A 300 W dc-to-dc boost converter and a 600 W, ac-to-dc power factor correction front-end boost converter prototype models are built in the laboratory. The experimental results confirm the theory. The resonant inductor used in the auxiliary circuit is coupled weakly to the boost inductor. Although parasitic oscillations are reduced due to the coupling, they are not completely eliminated. Hence, RC snubbers are required to suppress the oscillations. A ZVS auxiliary circuit assisted soft transition boost converter is also presented. Operating intervals of the proposed converter in various intervals of operation are analyzed. As all the parasitic elements in the circuit are accounted, parasitic oscillations are eliminated. A 300 W dc-to-dc converter operating at 250 kHz is built in the laboratory to verify the theory. A modified gating scheme to utilize the soft switching auxiliary circuit in the main power processing is also proposed. A 600 W, 100 kHz, 380 V dc, operating with universal input line voltage, ac-to-dc power factor corrected (PFC) boost converter is built using the proposed technique with modified gating algorithm. Large signal analysis to analyze the soft switching characteristics of the proposed technique during load and input voltage transients is also presented. PSPICE simulation results are presented to verify the theory. The proposed converter maintains soft switching during load and input voltage transients. The proposed auxiliary network is also extended to a family of pulse width modulated (PWM) converters. A two-switch soft switching boost converter is derived from the proposed converter. By integrating the proposed auxiliary network with a full bridge inverter, a ZVS dc link voltage source inverter (VSI) is obtained. Operating intervals of the proposed inverter in various intervals of operation for the forward power flow and reverse power flow are presented. A modified unipolar switching scheme to achieve ZVS during reverse power flow is also presented. The voltage stress on the VSI is clamped to the dc bus voltage in the proposed converter. The conduction losses are reduced as compared to other soft switching converters in the literature. As the proposed technique requires synchronized PWM operation, sine-ramp modulated PWM signals are used. Experimental results from a 120 V, 60 Hz, 300 VA, single phase VSI switching at 50 kHz are presented to verify the theory.

Description

Keywords

Electric current converters

Citation

URI

http://hdl.handle.net/1828/8972

Collections

ETD (Electronic Theses and Dissertations)
Theses (Electrical and Computer Engineering)
 
University of Victoria Libraries

We acknowledge and respect the Lək̓ʷəŋən (Songhees and Esquimalt) Peoples on whose territory the university stands, and the Lək̓ʷəŋən and W̱SÁNEĆ Peoples whose historical relationships with the land continue to this day.